-
DSM-less and happy
Future mod lists
Hey everyone,
Thought this would be a good thread to share what mods you would like to do in the future. I spent a good amount of time putting this together:
This is for my Slash 4x4 #6808
3767A Traxxas Shock Caps Aluminum Anodized Blue (4) $12.99
1664T Traxxas Shock Shafts Long Nitro Rustler (2) $9.39
6888X Traxxas Front Hardened Steel Drive Hub Slash 4x4 $4.29
6837X Traxxas Steering Blocks Aluminum Left & Right Slash 4x4 26.99 Not needed if Tekno kit used
6832X Traxxas Caster Blocks Aluminum Left & Right Slash 4x4 $38.99
1952X Traxxas Rear Stub Axle Aluminum (2) $21.69 Not needed if Tekno kit used
2656T Traxxas Shock Shafts Titanium XX-Long (2) $9.39
6877A Traxxas Cover Gear Clear Slash 4x4 $4.29
TKR6852X Tekno R/C M6 Rear Drveshaft/Hub Carriers 6mm $45.99
TKR6851X Tekno R/C M6 Fr Driveshaft/Steering Block 6mm $42.99
10130 MIP Rear X-Duty CVD Kit Slash/4x4 $59.99
6814 Traxxas Differential Kit Center Slash 4x4 $38.99 Replaces slipper clutch
6898 Traxxas Sway Bar Kit Slash 4x4 $22.59
3340 Traxxas Cooling Fan Velineon ESC $21.99
T8074BLUE Integy Motor Heatsink w/Cooling Fan Blue Slash $12.99
5611 Novak Y-Harness for Dual Cooling Fan Connection $7.59
81012 RPM Mud Flaps Bumper Slash $10.19
81030 RPM Tail Light Set Slash $9.49
RRC-10B RAMTech-RC Short Course Rear Bumper Light Kit $9.99 use with RPM Tail Light Set Slash
70392 RPM Front Shock Tower Slash/Stampede 4x4 $10.19
0090 JConcepts Illuzion Ford Raptor SVT Clear Slash/SC10 $35.70
PTR18 Traxxas SLASH 4x4 Bearing Kit Polyamide Sealed $49.99
TRX6860 King Headz Slash 4x4 Aluminum Motor Mount $35.99
2727 Lunsford Racing Titanium Turnbuckle Kit Slash 4x4 (7) $45.99
TRA039 RC Screwz Stainless Steel Screw Kit Traxxas Slash 4x4 $26.99
TRA039B RC Screwz Stainless Precision Metal Bearing Slash 4x4 $26.99
ST6845B STRC Aluminum Multi-Piece Steering Bellcrank set (blue) $35.99
I know the list is very extensive.... wish list...
-
its almost that time again
my wish list is just talked to tony at hobby town and the new castle 4s motor for the slash
have larry's mother in law paint my new body so i actually have one on it
will be gettin the fans shortly (just got them) or as soon as it warms up since i dont thermal unless above 70 outside
this sounds like something i could want hmm
6814 Traxxas Differential Kit Center Slash 4x4 $38.99 Replaces slipper clutch
as for the rest ill replace it when i break it lol
Last edited by Ricky Bobby; 01-09-2011 at 03:27 PM.
Reason: new parts
-
I wanna go fast...
why not just get the big bore shock kit? they have the aluminum caps(not blue) and they have the threaded bodies and titanium shafts
should be about the same price, and atleast you can keep your stock shocks together "just in case"
-
DSM-less and happy
I was thinking about that...
or just do the Ti rods, and the alum shock caps, and then these will be set.
options are out there...
-
Post whore
DON'T put the caps on the plastic body. One good hit it will break off and it's next to impossible to seperate. And as far the steering linkage is concerned I have never seen the strc one in use but I have had the traxxas one for the 2whl slash and it's JUNK. It is a known issue where the center link will wear away and one wheel will wander more then the other. Best steering I have used is the stock 4x4. Not much bling though
-
its almost that time again
if i get a pic to u could u show ur mother in law to get me a price to paint that silverado boddy i have
-
Post whore
-
its almost that time again
well got the rear diff open there is hardly any grease in there what so ever whats the best way to clean that out and what grease do u put back in or is there fluid to refill with and ive developed a nasty vibration at low speeds dont know if its tires or what will have to dig into that tomm hmm
-
I wanna go fast...
have you poked a hole in the tires? reading up on stuff it seems you need to "vent" the tires with a little hole because dirt and moisture can build up inside and without a way out could cause a vibration
-
I have an HPI RS4 Evo nitro that I'm turning into a drag car. I'm actually making my own parts and retro fitting 1/8 scale wheels to the 1/10th scale chassis.
Designing a one piece chassis that I'm going to get 3d printed so that everything from the motor mounts to the shock towers are part of the chassis eliminating a significant amount of bolts and weight.
-
Post whore
well that will have to get a pic on her. That sound sweet
As far as diff grease you can put at least 10,000 in the rear and 5,000-7,000 in the front. Thats kind of the ratio between the front and rear were you want to keep it. Since it will be out side most of the time you probably could go a little higher, but I don't know how high they go. I have used ofna brand diff grease.
-
Post whore
And one day I might have a nitro truck in which case I want to buy anything from this site!
http://www.rbinnovations.com/default.asp
-
its almost that time again
i vote nitrous
-
I wanna go fast...
nitrous for the baja 5t? OMG I gotta get it now!!
-
its almost that time again
im gonna need 5 and the hit at least
Posting Permissions
- You may not post new threads
- You may not post replies
- You may not post attachments
- You may not edit your posts
-
Forum Rules