So I'm lookin at subframe connectors as my next buy. I haven't decided on weld-ons or bolt-ons... Any thoughts??
Weld-on SFC
Bolt-on SFC
A blower for the Skylark
So I'm lookin at subframe connectors as my next buy. I haven't decided on weld-ons or bolt-ons... Any thoughts??
1991 Z/28
\m/(>.<)\m/
2006 Impala
Weld on.....All i see is ripping on bolt-on SFC's
94 Formula A4, ALL the Basic Bolt-ons. Best Time before Drag Radials and a Tune = 13.3 @ 104mph ( SOLD)
00 Maxima, SE 5-Speed, ( SOLD)
2011 Subaru Impreza WRX - WR Blue, Stage 1 Tune ONLY ( SOLD)
2012 Subaru Impreza STI - WR Blue
I run bolt ons since 2k miles and we all know my car is no virgin, no complaints from this cat.
2012 Cruze ECO M6 - Crystal Red- Just a little more boost than stock!
2001 Camaro SS - Rallye Red - In process.
I've heard good and bad about both. I'm kinda leanin towards the bolt-ons though.
Tom, what brand are you using?
1991 Z/28
\m/(>.<)\m/
2006 Impala
umm is this really a questions?
of course weld on bud
I run bolt ons on the wifes 67...no problems at all. They are alston pieces.
2012 Street Glide
1971 Vista Cruiser 455
2003 Duramax Dually Silverado 4x4
1986 442
I guess I'm kinda leaning away from the weld-ons since I don't know how to weld, nor do I know anyone that could weld em on for me. I've heard of the bolts bending/stretching/breaking, but I'm not running a 10 second monster. I'm just really sick of hearing all the "F-body squeaks" from every bump in the road....
1991 Z/28
\m/(>.<)\m/
2006 Impala
thats why you just get a shop or someone you know to weld them in...very easy to weld and you can weld up some of your torque boxes too while your in there. I don't see a point to bolt in as like you said below - the point of this is to connect your subframe to your unibody to prevent twisting and motion - you really think some lil bolts are gonna do much good? Your doing this for a reason, so do it all the way then so to speak. Your still going to have flex even if you have a 10sec car or a 14 sec car. I have seen hundreds of mustang subframes on and I don't think I have seen 1 that was not welded on - and this is one of the most basic of modifications.
After I have done these (make sure your body isn't preloaded too much) once they helped squeaking a bit, but usually your just hearing worn joints/suspension parts that these wont help much (mayyybe a lil)
steve
Originally Posted by Scales
Im going to recommend weld-in style sfc's.
Im also going to suggest the spohn set, they make really nice stuff and i wish i would have purchased them instead of my alstons. I hadnt done too much research before i made my purchase.
Alstons are great for straight line acceleration or drag purposes, but they also compromise a a bit of ground clearance.
Spohns set supports the subframe at different areas and are supposed to be better suited for corner carving heavy flex, of autocross...road race..heavy street use...while still affective for straight acceleration.
Im not completely positive where each attaches or exactly why which is better suited for what application this is just the overview i have noticed in my research.
NOTE: i havent installed my subframes yet, im not sure im going to either, i might try to sell them and go with a 6-point cage instead. My interior plastics were in terrible condition so they have been removed. A cage will tie the car together better than the sfc's and the car will look ok without a full interior IMO ...sorry for gettin off topic
I'm voting blower fpr the Buick
While I think a blower for the skylark would be really cool! I had to vote for the weld on's. They will give you much more support, longer life. Any muffler shop should be able to weld them in, or there may be a membeer or two here thaat can weld. If I were still living in Milwaukee I would be a ble to do it, unless you want to bring the car to Arkansas
Scoty
So like I said above... I have no one to weld anything for me. I suppose I could ask Dennis at the infumous Midus, but, what am I really gonna gain? I know people running bolt-ons, and they don't have problems. I have no problems hunting down a welder, I just wanna make sure it's worth my time and money.....
p.s. the Buick is not gettin a blower!!
(damn unrealistic voters)
Last edited by Scales; 09-23-2004 at 12:57 AM.
1991 Z/28
\m/(>.<)\m/
2006 Impala
Well i voted weld-in mainly do to the fact that spohn offers a superior design, which is only attainable in weld-in style sfc.
Plus once its on you wont ever have to worry about nuts backing off, or expansion of the bolt holes(however unrealistic). Do it right once and forget about it.
Make sure the suspension is loaded when they are being installed.
Just trying to keep ya from regretting.
blower for the buick...you drive it more
99 GTP
Originally Posted by bustamove
Ohhhhh... Dem's fightin words!!
Stop by me tomorrow at work on 1 of your 184 breaks.
1991 Z/28
\m/(>.<)\m/
2006 Impala
Mine are welded in. There are customs... but before I got these I was going to get the Spohn ones.
-Tyler
Don't drink and Post!
1991 Camaro, LS1 Powered -- 2000 Silverado 1500Originally Posted by BadAzzGTA89
i have weld ones.. .they are custom made and damn.. do they help handling..
Recommendations on reputable places to have weld in SFC's installed??
Rod and Competition in Butler call Pat@262-781-9044 tell him ryan sent you.
O ya i like the blower for the skylark.