Need a 4.6 long block 2V for a 96-XX mustang. needs to be running and in good shape. PM me if you have anything.
Need a 4.6 long block 2V for a 96-XX mustang. needs to be running and in good shape. PM me if you have anything.
70 cutlass 442- dads car
95 stang- Stock long block 195,XXX miles
03 XC600 - bone stock (still faster then smokin ram)
03 Polaris predator- 4.250 bore (assembly required)
84- 4 eyed
this is a hell of a deal and I believe it's still for sale
http://www.midwestmustangassociation...ighlight=motor
needs a password.... can you copy past the info? hes ready to pull the trigger on a motor like yesterday... we may opt for the 99 and up PI motor, but that depends on what this one looks like... thanks!!
70 cutlass 442- dads car
95 stang- Stock long block 195,XXX miles
03 XC600 - bone stock (still faster then smokin ram)
03 Polaris predator- 4.250 bore (assembly required)
84- 4 eyed
*SERIOUS INQUIRES ONLY!*
The PI headed motor out of my car will be up for sale.
This will be a longblock.
Less then 30K on Engine
Full PI Swap
Heads have been P&P'd (Over $700 just in the headwork) and the combustion chambers altered to bring it back to stock compression ratio
Stock '98 bottom end
Newer PI Intake with aluminum crossover tube
This motor made 249.9 on the dyno a couple of years ago (magazine article to verify)
Car has gone a 12.76 with me driving at 3350lbs
This is the perfect engine if you are looking to drop it in your Non PI car or for a V6-V8 swap
The engine is still in the car and you can hear it run.
I will be keeping the intake plenum just so you know (Putting it on Mom's Car)
Any questions email me damonsteinke@yahoo.com or call me 608-712-6900
I will not ship
Located in 53590
Will not just give away either so don't bother asking if I will sell it for cheap as dirt.
$1000 OBO
If you think the price is high then make an offer, that's what OBO means
Political signatures are not allowed
I have an engine wiring harness for a 2002 GT that was pulled off after the new car only had about 200 miles on it.
that is a bit high, but if he will take a decent offer... i found a stock one out of a 03 town car with 56,XXX for $800 shipped.. so we will see.... what do you want to the harness if we need it?
70 cutlass 442- dads car
95 stang- Stock long block 195,XXX miles
03 XC600 - bone stock (still faster then smokin ram)
03 Polaris predator- 4.250 bore (assembly required)
84- 4 eyed
Make me an offer. I was going to throw it in the garbage but decided to hang onto it because it's basically brand ne
just let me know what nite you throw it in the garbage let me make sure i dont need it... i can get back to you by the end of the weekend!
70 cutlass 442- dads car
95 stang- Stock long block 195,XXX miles
03 XC600 - bone stock (still faster then smokin ram)
03 Polaris predator- 4.250 bore (assembly required)
84- 4 eyed
Anytime. It's not going anywhere right away because it's in a box in my closet.
Just email me. I'll get it directly on my blackberry. bb@artbynicholas.com
I'll check back here too.
The engine is still for sale. I would need a couple of days to finish pulling it. I need it gone asap to get my other one. I will be off work tomorrow if you want to call or I will check in here throughout the day today
In Progress
604BBF/TH400/Radials
can you call me. 262-385-0894. I just put an offer on one on ebay right now, but would like to do it locally. cash in hand. Thanks, Jon
70 cutlass 442- dads car
95 stang- Stock long block 195,XXX miles
03 XC600 - bone stock (still faster then smokin ram)
03 Polaris predator- 4.250 bore (assembly required)
84- 4 eyed
I work til midnight. email me...
Last edited by Stangman98; 03-21-2009 at 03:36 PM.
In Progress
604BBF/TH400/Radials
pm sent!
70 cutlass 442- dads car
95 stang- Stock long block 195,XXX miles
03 XC600 - bone stock (still faster then smokin ram)
03 Polaris predator- 4.250 bore (assembly required)
84- 4 eyed
PM Replied
In Progress
604BBF/TH400/Radials
32xxx mile 4v 4.6 motor out of a 98 cobra 1300 obo
Sold
In Progress
604BBF/TH400/Radials
PM Sent
In Progress
604BBF/TH400/Radials