Any good shops in the area

**1loudrex** · 01-07-2007, 09:13 PM

Ive got a 2002 Wrx and I need the clutch replaced. I have the clutch kit but ill need the flywheel resurfaced.

Ive got Automatic Transmission and Design in mind since I have a few buddies that work there, but any other shops with a decent price would be good to.

Thanks for any help
Dan

**Flicktitty** · 01-07-2007, 09:15 PM

uh, i Know Jake (topstreet) has done some Sube work he might do it for you? i'm not sure though or maybe BEE Yond might do it to?

**ThatWhiteCivic** · 01-07-2007, 11:12 PM

Yeah Bee did my buddy Mark's clutch and tranny on his Sube

**TopStreetDsm** · 01-07-2007, 11:39 PM

Thanks Flick, But I am down to basically working on my car and truck at this point... (and twicks69's tranies :p) Good luck to you with the project LoudRex!

**Flicktitty** · 01-08-2007, 12:32 AM

yeah i kindda figured that but i'd just throw it out there.

Where you been i haven't seen you on much latley?

**sloLs1** · 01-08-2007, 07:15 AM

Originally Posted by 1loudrex

Ive got a 2002 Wrx and I need the clutch replaced. I have the clutch kit but ill need the flywheel resurfaced.

Ive got Automatic Transmission and Design in mind since I have a few buddies that work there, but any other shops with a decent price would be good to.

Thanks for any help
Dan

my shop would do it... i can get you a price today...

**tommyt5078** · 01-08-2007, 09:42 AM

I say visit the subaru forums NASIOC.COM go to local forum MWSOC and find Tim Sanderson................

**jbiscuit** · 01-08-2007, 09:54 AM

+1 for Tim Sanderson

**TopStreetDsm** · 01-08-2007, 12:28 PM

Originally Posted by FlickNtitty

Where you been i haven't seen you on much latley?

I have been on computer probabition...

No... I just moved... Again... and I have been with out that there inter-web for a while. Snapped the timing guide in the daily driver so... Basically, in a nut shell... stroken it.

**sloLs1** · 01-08-2007, 02:59 PM

Originally Posted by sloLs1

my shop would do it... i can get you a price today...

your cost would be $460 for the labor.... let me know if your intrested... i have done subies before... they arent bad at all.... A LOT easier than a EVO!!!

Originally Posted by TopStreetDsm

.....Snapped the timing guide in the daily driver so... Basically, in a nut shell... stroken it.......

**Flicktitty** · 01-08-2007, 03:32 PM

that sucks where'd you end up moving too.

Originally Posted by TopStreetDsm

I have been on computer probabition...

No... I just moved... Again... and I have been with out that there inter-web for a while. Snapped the timing guide in the daily driver so... Basically, in a nut shell... stroken it.

**TopStreetDsm** · 01-08-2007, 09:13 PM

Back out in waukesha again...

**Bee** · 01-11-2007, 07:55 PM

Originally Posted by FlickNtitty

uh, i Know Jake (topstreet) has done some Sube work he might do it for you? i'm not sure though or maybe BEE Yond might do it to?

we've done a few...wrx/sti no biggy!!! tranny rebuilt also available in 2-3 day wait... sube trannys break quite often...

sube tranny install: $300.00
resurface flywheel: $50.00
all done in a day too!!!

Yes we can beat any written or advertised price gauranteed!!!

I'll update pixs of our NEW in-house dynamometer, Fabrication division, Show room, Race car section, Custom muffler bays, General Auto maintenance bays, and tire machine section..... 9 bays total..... with tons of outlot parking(10-12 in front & 40-50 car in the rear)... car show maybe.. or even dyno days w/ a BBQ fest.... I'll upate on car shows/dyno days/BBQs!!!

8025 N. 76th ST. near Brown Deer.... come check it out!!!

**TurboAWD2.0** · 01-12-2007, 04:12 AM

Or, and no offense to anyone here, take the flywheel to napa. It's $36 or something like that to get it resurfaced. Then, do the whole thing yourself in your garage

EDIT:

On a side note, what mods did you have when you ran that 14.12 sec quarter?

**Bart H** · 01-12-2007, 02:28 PM

Tim Sanderson FTW!

**Bee** · 01-12-2007, 10:00 PM

if you are mechanically inclined then yes do it in your garage... be careful that tranny can come down on you....

**1loudrex** · 03-12-2007, 09:52 PM

Originally Posted by TurboAWD2.0

Or, and no offense to anyone here, take the flywheel to napa. It's $36 or something like that to get it resurfaced. Then, do the whole thing yourself in your garage

EDIT:

On a side note, what mods did you have when you ran that 14.12 sec quarter?

Perrin Uppipe.

95excoupe · 03-12-2007, 10:42 PM

Originally Posted by Bee

we've done a few...wrx/sti no biggy!!! tranny rebuilt also available in 2-3 day wait... sube trannys break quite often...

sube tranny install: $300.00
resurface flywheel: $50.00
all done in a day too!!!

Yes we can beat any written or advertised price gauranteed!!!

I'll update pixs of our NEW in-house dynamometer, Fabrication division, Show room, Race car section, Custom muffler bays, General Auto maintenance bays, and tire machine section..... 9 bays total..... with tons of outlot parking(10-12 in front & 40-50 car in the rear)... car show maybe.. or even dyno days w/ a BBQ fest.... I'll upate on car shows/dyno days/BBQs!!!

8025 N. 76th ST. near Brown Deer.... come check it out!!!

yes, its very true. i say one of the best shops in wi. and good quality of work.

people say beeyond is blah blah, but my point of view they just are haters.

**bearsek** · 03-12-2007, 11:14 PM

We work on subies all the time(Extreme parts). They are for sure easier than evo clutches

**civic600** · 03-18-2007, 01:41 PM

take it to extreme parts.....they do awesome work

Thread: Any good shops in the area

Thread Tools

Rate This Thread

Display

Any good shops in the area

Posting Permissions