LS1 TB porting.

[GTSLOW]

Anyone self ported their throttle body? Just yanked mine off tonite, wholy shiat this mofos restrictive!!! It goes from like 75mm by the blade to 65mm then opens back up. Gonna level it out all the way from the blade to the opening.



Anyone else done this?

[BAD LS1]

Check the pic, Just a die grinder ands a couple sanding drums:

[GTSLOW]

Very nice!! Did you cut half the rod off the holds the throttle blade? I did dunno how much it helped tho.

I spent about 30 bucks on new bits for my dremel and some 220 grit sand paper. Was on it from 10pm to 3am this morning. Then wokeup and sanded a lil more. It's nice and smooth now.

Throttle response is insane now too!! Half throttle = spinning tires

[USMARINE1108]

I did mine. Make sure you don't overfill the idle air port with epoxy. I did that at first and it was fine until the cam went in. I had to take it off and grind that crap out. Also make sure you don't port around the area where the blade rests....leaving a gap even with the blade when closed. It gets close there.

[SLOWC5]

I had this one done

[Yooformula]

Is there really that much of a difference or is it more of peace of mind knowing every mod has been done?

[USMARINE1108]

Is there really that much of a difference or is it more of peace of mind knowing every mod has been done?

I'm sure it helps a little bit, but didn't notice anything. When you have 300hp, you're not going to notice 3-5hp in the seat of your pants. I did mine, just like you said, to know it's done.

[GTSLOW]

Is there really that much of a difference or is it more of peace of mind knowing every mod has been done?

IMO there is a big difference in throttle response. Spins em in 1st alot worse than it did before too.

[SSmike1]

IMO there is a big difference in throttle response. Spins em in 1st alot worse than it did before too.

awww
your just Imagining things!


your Head is Spinning EASIER TOO!

[A B4C Z]

SHANNER S3

[Crawlin]

I never had it on my car. hell i have the ls1 intake going back on it

[BAD LS1]

It makes a diff in responce is about it, your essentially increasing velocity or CFM into the manifold, that creates a very mild supercharging effect. Thats what gives the better responce.

Larger engines are in need of it, as the stock 75mm TB is a bottle neck.

[Crawlin]

i have a stock LS1 engine

[SLOWC5]

i have a stock LS1 engine

^ here we go again....

[Crawlin]

hahaha, i might as well put a stock shortblock in it, would go faster.

anyways, i've heard both sides, that they have felt it, and others who said it wasn't crap. to me, on a stock TB i don't want to mess with it, because the ACTUAL throttle blade will always be the same diameter. so that SAME restriction is always there regarding size. so porting the front/back area and the time spent, to the edge leading up to the blade, just isn't worth it for me.

[Yooformula]

so that SAME restriction is always there regarding size. so porting the front/back area and the time spent, to the edge leading up to the blade, just isn't worth it for me.

thats kinda what I was thinking

[BAD LS1]

Right, you cant physically get TOO much more in due to the size of the hole. All your doing is speeding the air up going in through that small hole, via a smoother "funnel effect" if you will.

[A B4C Z]

Gone mine done its a Shanner s3 on the ls1 fourms he does them. Looks good id snap a shot but my computer is broke to upload them.

[GTSLOW]

Gone mine done its a Shanner s3 on the ls1 fourms he does them. Looks good id snap a shot but my computer is broke to upload them.

Shaners are teh sex of tb's!!! You got the one with the filled in part too???

[LITE SPD]

Mine is also a Shaner S3.