Where is a pic with the t-tops off and your mullet flowing in the breeze kev? :rolf u ever get some sticky tires for that thing??
Printable View
Where is a pic with the t-tops off and your mullet flowing in the breeze kev? :rolf u ever get some sticky tires for that thing??
I want a third gen.......but just don't have room for one.
I'd be interested to learn more about this....hoping to do some TPI tuning this summer to mine, sorry no 3rd gen pics or car here to share though :( ;) . I'm assuming you will run the first of this harness on your car? I am curious to see how it goes.
For the 3rd genners: http://jalopnik.com/360720/camaro-du...d-water-heater
:D , a waste of a clean Camaro shell....but interesting anyway.
http://brewcitymuscle.com/forum/atta...1&d=1204080546
http://brewcitymuscle.com/forum/atta...1&d=1204080546
Deanna, when do you want to line up the to the Iroc to me?? :headbang Noooo, i'm not gonna even try the cutty!!:fire
Hey BadAzzGTA89, Nice lookin bird! Didn't I sell you those SLP Runners I used to have? Did you ever make good use of em?
Awww Mikey cmon.....the cutty is gonna be out this year too and I'll give ya some land ;)
The iroc needs some tlc before I race ya this year, it's been sitting for a while now. Hell the plugs and wires are 10 years old I believe...not even kidding either. First thing on my "to do" list for that is the tune up, even though I'm sure it'll get romped by ur purple beast:wow
the 08 season drag car...turbo 3rd gen FTW!!
http://i42.photobucket.com/albums/e3...d/100_1149.jpg
Well its a little more than just a harness. This is basicaly a hybrid setup that uses alot of the parts from the vortec 350 in trucks/vans from 96-00. In 01 the chevy express van with the vortec 350 had the 411 computer so thats the cal file you start with, and because that van was offered in a 1 ton, you can set it up to run either the 4L60e or the 4L80e (but not both, have to pic one)
Cheep way to do it:
Find a 01 chevy express van in the junk yard and take the following parts:
-Complete wiring harness
-Distributor(or cam sensor, its alot like the opti spark but not as problematic)
-Timing cover (its plastic be careful it doesnt break)
-Reluctor wheel (its under the timing cover infront of the crank gear)
-Harmonic balancer (you can use the one you have if you machine down the snout the thicknes of the reluctor wheel)
My way to do it:
-Build a new harness that has only the stuff I need in it
-Accel Billet Distributor (only after market vortec distributor, after you break a few stockers you realize why I want this one)
-Comp Aluminum Timing cover, modified with a threaded hole for the crank sensor.
-Stock reluctor wheel
-ATI blancer cut down to the correct length.
I suppose I should just start a new thread about this so it doesn't crap this one up but at the same time, this is probably only of interest to people in here. As far as Cost I have no idea, There is a guy selling this already and I think hes getting about $200-$400 depending on what you all need.
Here are mine:
Just after I got it from Indiana, haven't done anything to it yet it kind of turned into a DD because the 305 gets better gas than my hemi.
http://i193.photobucket.com/albums/z.../DSC098511.jpg
Pics of my 85 when I bought it, it is now at the bodyshop for a few minor things :shades I'll post pics when I get it back.
http://i193.photobucket.com/albums/z...PICT2919-1.jpg
http://i193.photobucket.com/albums/z...PICT2921-1.jpg
I can see that I need to get some pics of mine up.
I will have a set of nittos on iroc rims for sale soon if anyone is looking.
Kevin the computer thing sounds interesting.
Kory